> Conventional Fire Systems>ActiV Sounders & VADs>ActiV Conventional O-R-3-2.5-17 Base VAD c/w 96dB(A) Sounder
O-R-3-2.5-17 ActiV Conventional Base VAD c/w 96dB(A) Sounder View larger

ActiV Conventional O-R-3-2.5-17 Base VAD c/w 96dB(A) Sounder

BF432C/CC/W

New

  • Third-party certified to EN54-3 (Sounders) and EN54-23 (VADs).
  • Provides 'O-R-3-2.5-17' light distribution. 
  • Ideally suited for use in corridors and other rectangular areas.
  • Impressive 96dB(A) sound output @ 1m.
  • 31 selectable primary and secondary tone pairs and two volume levels (high and low)
  • Three selectable VAD flash rates (0.5Hz, 1Hz, OFF)
  • Alarm Current at 30Vdc = 12.2mA (0.5Hz) or 19.5mA (1Hz)
  • Alarm Current at 18Vdc = 14.5mA (0.5Hz) or 25mA (1Hz)
  • Optional BF330CTLIDW white or BF330CTLIDR red cap available for stand-alone use.
  • Supplied with a BF431QCP quick connect plate and detector spur wires.
  • IP21C rated.

LPCB  CE

By buying this product you can collect up to 27 loyalty points. Your cart will total 27 points that can be converted into a voucher of $5.40.


By buying this product you can collect up to 27 loyalty points. Your cart will total 27 points that can be converted into a voucher of $5.40.


Technical Specifications

Approvals/certificationsCertified to EN54-3 & 23 by the LPCB.
Protocol/compatibilityCompatible with C-TEC's CFP, FP, MFP and EP203 conventional fire alarm panels and virtually all other makes (testing on third-party panels is recommended before use)
Application/operationDesigned to be ceiling mounted - either stand-alone with a red or white cap or as part of a stacked Sounder/VAD/Detector Base combination.
VAD category & coverageO-R-3-2.5-17 Rectangular coverage - ideal for corridor spaces.
Flash rate & colour0.5Hz; 1Hz or OFF / White.
Supply/operating voltage18 to 30V DC.
Nominal SPL (Sound Pressure Level)96dB(A).
Alarm currentAt 30Vdc: 12.2mA (0.5Hz) or 19.5mA (1Hz); At 18Vdc: 14.5mA (0.5Hz) or 25mA (1Hz)
Product dimensions (mm)122mm diameter x 46mm deep (not including optional detector and base).
IP RatingIP21C (Type A).
Weight170g.
Operating conditions/temperature-10ºC to +55ºC. Max. 95% RH (Non-condensing).
NotesFor compliance to EN 54-3 & EN54-23, the BF431QCP Quick Connect Plate must be used with the base device.

Documentation

BF431QCP Quick Connect Plate

DFU4310020 Rev 1

Download (237.49k)

ActiV Base VAD Sndr Insts

DFU4311000 Rev 9

Download (411.99k)

ActiV Sounder VAD flyer

DML0547900 Rev 1

Download (2.25M)

Conv Base Range Polar Diag

DFU4311010 Rev 1

Download (267.81k)

8 other products in the same category:

Approval Certificates

Approval Certificate (LPCB)

Download

EC Certificate of Conformity (CPR)

Download

Declaration of Performance (C-TEC)

Download

Declaration of Conformity (C-TEC)

Download

Approval Certificate (VdS)

Download

VAD coverage (with multiplication factors applied)

VAD coverage depends on factors such as ambient light and viewing angle (direct or indirect). The table below summarises how the coverage of the BF432C/CC/W increases or decreases based on these factors. To use the table, calculate the lux level of the area requiring coverage, determine whether the viewing angle will be direct or indirect then read off the coverage in the relevant column. For further information refer to our VAD System Design Guide, downloadable from the Documentation tab below.

Lux level in area requiring coverageCeiling Mounted Direct ViewingCeiling Mounted Indirect Viewing
000-101 lux8.4m H x 7.0m W x 47.6m L3.9m H x 3.25m W x 22.1m L
101-200 lux7.2m H x 6.0m W x 40.8m L3.6m H x 3.0m W x 20.4m L
201-300 lux5.7m H x 4.5m W x 32.3m L3.0m H x 2.5m W x 17.0m L
301-400 lux4.2m H x 3.5m W x 23.8m L2.4m H x 2.0m W x 13.6m L
401-500 lux3.3m H x 2.7m W x 18.7m L1.8m H x 1.5m W x 10.2m L
501-600 lux2.7m H x 2.2m W x 15.3m L1.5m H x 1.2 W x 8.5m L
601-700 lux2.1m H x 1.7m W x 11.9 Lnot applicable
701-800 lux1.5m H x 1.2 W x 8.5m Lnot applicable